Request a quote

How can water losses in an installation be reduced?

How can water losses in an installation be reduced?

Reducing leaks and level drops in a facility first requires distinguishing between equipment defects, biological imbalances, or poorly adapted operation. In a pond, irrigation basin, agricultural reservoir, or settling structure, a few centimeters less can represent a considerable volume. Regular monitoring of the water level therefore allows for action before top-ups become too frequent, costly, or insufficient.

A proper diagnosis is not just about looking for a crack. Evaporation, overflows, silting, invasive vegetation, frequent washing cycles, or poorly controlled circulation can also explain an unusual drop. The goal is to preserve the available resource while maintaining the facility's uses: irrigation, storage, regulation, treatment, or supplying equipment.

Precisely identify the origin of the drop in level

Before any intervention, it is essential to observe the evolution of the body of water over time. A gradual decrease during hot weather does not have the same significance as a rapid drop, visible even in cool weather. Recording the level at fixed intervals, noting precipitation, and comparing added volumes provide a reliable basis. This simple method helps to distinguish a seasonal phenomenon from a real anomaly.

Evaporation depends on temperature, wind, sunlight, and the exposed surface area. It can become significant in a wide, shallow basin. However, it should not be used as an automatic explanation. When makeup water requirements increase without an obvious change in weather, the banks, outlet structures, pipes, and wetlands around the site must be examined. An unexplained and lasting drop warrants an in-depth analysis.

Check the visible technical elements

Manholes, valves, overflows, fittings, pumps, and pipes must be inspected methodically. A worn gasket, a valve that closes poorly, or a damaged pipe can lead to a discreet but continuous leak. In systems equipped with pumping, unstable pressure or an increased filling time can also signal a problem. It is useful to consult the possible causes of flow difficulties in a basin in order to relate the observed symptoms to the overall operation of the structure.

The inspection must also cover overflows. An incorrectly sized, obstructed, or improperly installed overflow can discharge water without it being immediately noticed. After a rainy episode, checking for flow marks on the banks and around the equipment often helps to identify an uncontrolled discharge. This vigilance prevents stored water from being lost at the very moment when the installation should be conserving it.

Take action on the silting and the configuration of the basin

The accumulation of sediment gradually reduces the useful depth of a body of water. With an identical surface volume, a basin that has become shallow warms up faster and offers more area exposed to evaporation. Silt can also disrupt exchanges, promote certain plant growth, and limit storage capacity. Preserving a sufficient functional depth is therefore an important lever for retaining water for longer.

Proper maintenance does not necessarily mean a major intervention on the entire bottom. It begins by identifying the most affected areas, the points of material inflow, and the sectors where deposits accumulate. The role of ecological design in limiting sediment is detailed in this article on preventing basin siltation. A coherent approach combines managing inputs, water circulation, and maintaining a truly available storage volume.

The banks are also important. A weakened slope can bring in soil during rains, while poorly managed vegetation can alter water circulation and complicate maintenance. Conversely, thoughtful revegetation helps to stabilize certain areas. A balance must be sought between bank protection, equipment accessibility, and limiting the input of fine materials.

Limit the biological imbalances that increase water needs

Invasive algae and aquatic plants can significantly alter the behavior of a pond, pool, or reservoir. Overly dense vegetation increases exchanges with the atmosphere, sometimes slows circulation, and makes it more difficult to observe the actual water level. During hot periods, these imbalances can increase the need for replenishment. The priority is to restore a stable and legible aquatic environment, without treating the symptoms in isolation.

In a retention basin, a hillside reservoir, or a hydraulic structure, the needs are not the same as those of a landscaped body of water. However, the principle remains the same: analyze the causes before choosing a solution. When the level drops faster than expected and impermeability seems not to be the issue, a study of the increase in water requirements for a body of water can guide the diagnosis toward the biological and physical factors involved.

Improve the operation without shifting the problem

Reducing losses also involves daily habits. Scheduling refills during the coolest hours, avoiding overflows during additions, and adjusting withdrawals to actual needs limit waste. For installations equipped with pumps, it is advisable to ensure that the flow rate, pressure, and operating time correspond to the expected result. Equipment that is straining can degrade the control of the volumes withdrawn and increase energy expenses.

The implementation of simple indicators facilitates monitoring: water level, frequency of top-ups, pumping duration, state of the banks, and presence of excessive vegetation. These data do not need to be complex to be useful. They allow for the identification of slow changes and the measurement of the effect of actions taken. Management based on comparable observations is more effective than ad hoc intervention carried out in an emergency.

Implement a sustainable preservation approach

Reducing water losses does not consist of constantly compensating with new supplies. A sustainable solution relies on a global diagnosis: the state of the bed, circulation, technical structures, water quality, vegetation, and uses. This vision is particularly relevant for lakes, ponds, storm basins, irrigation reservoirs, and reserves intended for agriculture or snowmaking.

By combining preventive maintenance, equipment inspection, and the treatment of aquatic imbalances, it becomes possible to conserve more useful water in the installation. Each site has its own constraints, but the method remains constant: observe, identify the dominant cause, correct without weakening the environment, and then monitor the results over time. It is this consistency that protects the resource, the uses, and the longevity of the structure.

Do you have a question?

Contact us